Cylinderhead | Motor | Camshaft | Exhaust | Cooling | Fuel System | Clutch System | Piston | Connecting Rod | Oil System | Transmission | Suspension | Brakes | Electrical | Special Fasteners | Kits | Consumables |

Item: Independent Front Suspension

Part #: 13-01
Description: Independent front suspension consisting of cross member and two a-arms for Fiat 600 chassis automobiles. complete with mounting hardware.

Part #: 13-02
Description: Independent front suspension consisting of cross member and two a-arms for Fiat 850 chassis automobiles. complete with mounting hardware.

Part #: 13-03
Description: Independent front suspension consisting of cross member and two a-arms for Fiat 500 chassis automobiles. complete with mounting hardware.

Part #: 13-12
Description: Front Stabilizer Bar for Fiat 600 type chassis.  Requires some fabrication for installation.

Part #: 13-16
Description: Replacement a-arm RT or LT for Item 13-01 and 13-02

Part #: 13-17
Description: Upper trunnion adjuster kit.  Allows the relocation of upper arm for proper geometry realignment. Raises in-board end of upper a-arm to reduce camber and toe steer change.

Part #: 13-18
Description: Replacement standard bushing set of in-board end of upper a-arm.

Part #: 13-23
Description: Idler arm bracket.  Specify Fiat 600 or 850, RT or LT hand drive vehicle.

 

Item: Rear Suspension

Part #: 13-04
Description: Tubular rear suspension patterned on the original Abarth "Pendolare" suspension.  These will fit the standard chassis mounts without modification.  Arms can be ordered for use with standard Fiat 600D/850 axle assemblies or for use with S/T rear axle assemblies.  Please specify.

Part #: 13-05
Description:  Exact copy of complete Abarth Pendolare rear suspension.  Includes arms, bearing carrier, brake caliper bracket, and stub axle.  Bearing are not included.  These items are fully interchangeable with original Abarth components.

Part #: 13-25
Description: Abarth TC rear spring (for use with standard shock absorbers).  Lowers rear of car 1.5 inches. 

 

Item:  Replacement A-arm

Part #:
  13-16
Description:  Replacement A-Arm for items 13-01 and 13-02.  May be used for either RT or LT side.

Item: 3-piece Modular Road Wheel

Part #: 13-30
Description: Aluminium wheel, 3-piece modular.  Cast aluminum center with spun aluminium inner and outer halves.  Any width from 5.5-10 inches, 13 inch diameter, 98mm bolt circle diameter.  Specify offset required.

Item:  Reproduction Aluminum Campagnolo Wheel

Part #: 13-31
Description: Aluminium reproduction Campagnolo wheel, 5.5 inch width with the proper offset for Abarth 750 GT, Sestriere and Allemano chassis.

Part #: 13-31
Description: Aluminium front wheel hub assembly.  This includes bearing adapters to fit larger wheel bearings to the standard spindle.  Seperate mounting flanges for wheel and disc brake rotor.

Item:  Upper A-Arm Trunnion Kit

Part #: 13-17
Description: Upper A-arm trunnion adjuster kit.  Allows inner end of upper a-arm to be raised to compensate for lowered front suspension.  Reduces the amount of camber change.

Item:  Shock Absorber

Part #:  13-08
Description:  Front shock absorber with 18 range adjustment.  Comes with adjustable spring height platform.  Made exclusively for S/T by Pozzi in Argentina.   Compatible with Items 13-01 and 13-02.  Please order spring seperately

Item:  Shock Absorber

Part #:  13-09
Description:  Rear shock absorber with 18 range adjustment.  Comes with adjustable spring height platform.  Made exclusively for S/T by Pozzi in Argentina.   Please order spring seperately.

 
Specialist Services
Calendar and Race Reports


Gallery